My DB2 Build
#1
My DB2 Build
Alright so I'm bored and decided what better time to make a build thread and entertain myself and others.
I've been around Hondas for a long time. Some people here make remember me and my 1st EG hatch (blue, slammed, fart can, amber turns, autotragic circa 2001-2002). Since then I've had a 89 5.0L Mustang notch back, 89 Prelude Si 4WS, 94 Grand Cherokee all jacked up on mudders, 93 CX hatch beater, 93 Grand Cherokee V8 and finally my 93 GS-R. I bought the Teg because gas prices were nuts and my commute is about 60km one way to work (crap).
Anyhow, here's the car in all it's glory shortly after buying it. I add 1 pieces, ITR style lip, amber turns and of course, stickers!
I've been around Hondas for a long time. Some people here make remember me and my 1st EG hatch (blue, slammed, fart can, amber turns, autotragic circa 2001-2002). Since then I've had a 89 5.0L Mustang notch back, 89 Prelude Si 4WS, 94 Grand Cherokee all jacked up on mudders, 93 CX hatch beater, 93 Grand Cherokee V8 and finally my 93 GS-R. I bought the Teg because gas prices were nuts and my commute is about 60km one way to work (crap).
Anyhow, here's the car in all it's glory shortly after buying it. I add 1 pieces, ITR style lip, amber turns and of course, stickers!
#2
Then I picked up parts to do my S2000 cluster install.
Modifry ECT converter:
Electronic VSS:
Started wiring the S2000 cluster plugs to spare DA cluster plugs I pick up.
I've got over 20 hours worth of work into the harness. Had to figure out all the DA wiring with a spare cluster, total pain.
Then soldered it into the car:
Then did a little trial run of it (no speedo or ECT at this time):
Here's a little vid and some driving, ignore my dumb comments.
And a night vid.
Modifry ECT converter:
Electronic VSS:
Started wiring the S2000 cluster plugs to spare DA cluster plugs I pick up.
I've got over 20 hours worth of work into the harness. Had to figure out all the DA wiring with a spare cluster, total pain.
Then soldered it into the car:
Then did a little trial run of it (no speedo or ECT at this time):
Here's a little vid and some driving, ignore my dumb comments.
And a night vid.
#4
Bought NSX calipers for my front brakes:
Installed some Pro Sport Oil Pressure and Temp Gauges:
Most important part, videos!
http://www.youtube.com/watch?v=IdviENH7Euw
http://www.youtube.com/watch?v=qjanU4LZ0Og
Also put in a C-Pillar bar.
I decided to slightly tint/smoke my spare tails and bumper turns. I'm pleased with the out come. They won't go on till spring time.
PIC Apex 10k front/8k rear and Blox Rear LCAs have been ordered.
Installed some Pro Sport Oil Pressure and Temp Gauges:
Most important part, videos!
http://www.youtube.com/watch?v=IdviENH7Euw
http://www.youtube.com/watch?v=qjanU4LZ0Og
Also put in a C-Pillar bar.
I decided to slightly tint/smoke my spare tails and bumper turns. I'm pleased with the out come. They won't go on till spring time.
PIC Apex 10k front/8k rear and Blox Rear LCAs have been ordered.
#5
And that's where I end off.
I've got a B18B block and I might build up an LS/VTEC motor but anyone who knows me knows my mind changes one day to the next.
Right now I'm gonna re do my suspension, get some new rims, some exterior ----, brakes, etc.
Enjoy!
I've got a B18B block and I might build up an LS/VTEC motor but anyone who knows me knows my mind changes one day to the next.
Right now I'm gonna re do my suspension, get some new rims, some exterior ----, brakes, etc.
Enjoy!
#7
Looking sick! you having a tough time doing the speedo cable? man I hope you post a DIY for the cluster i love it! Nice to see more DA builds comin through! DA love!
Ive got smoked tails comin on and turn signals too lol, just waiting for seasonal change :P
Ive got smoked tails comin on and turn signals too lol, just waiting for seasonal change :P
#8
I just need some side markers and a new set of 1 pieces, mine are cracked.
#9
does the rear strut bar really do anything? if so is it noticeable? i wanna get a rear subframe brace but i just need the dimensions so i can get 1 lazer cut @ work... id rather 1 off it so i can lazer in a design
this is what my current setup looks like
this is what my current setup looks like
Last edited by blown90b16teg@11psi; 12-21-2008 at 10:39 PM.
#10
Strut bar is just a no name BS Pac Mall Piece. My old EG had some Skunk2 stuff on it and I noticed a big difference. The brand name stuff is generally more stiff and not flexy like the cheap brands. I can grab my megan c-pillar bar and almost bend it, good thing it was cheaper.
I need a swap bar and I like the bling of the ASR.
OOOO SHINEY!
I need a swap bar and I like the bling of the ASR.
OOOO SHINEY!
#11
yeah im thinking bout a cage i was bored @ work 1 dayand decided to mock 1 up. but right now thats on hold as i just got laid off...but i have one more week in jans o ill prob finish the mock cage and enclose the front seats and engine bay
Last edited by blown90b16teg@11psi; 12-21-2008 at 11:09 PM.
#12
I won't be doing a cage till the car is no longer a DD and still it will never be a total race car. I like to cruise and ---- lol.
Next set of mods are ASR brace and rear sway bar, ST front sway bar, rear tie bars (EM racing maybe), full bushing kit. I might do a camber kit, not sure yet. Then it's get my NSX brakes on the front and RSX brakes on the rear.
Next set of mods are ASR brace and rear sway bar, ST front sway bar, rear tie bars (EM racing maybe), full bushing kit. I might do a camber kit, not sure yet. Then it's get my NSX brakes on the front and RSX brakes on the rear.
#13
my car is a DD and i still want to do the cage... rsx brakes on the rear.. really how much bigger than stock. as i have to get bigger brakes on the rear. once u have the nsx calipers on id like a ride would like to compare between my wilwood bbk
Last edited by blown90b16teg@11psi; 12-21-2008 at 11:32 PM.
#14
It's just RSX calipers really. Using EP3 rotors since they are 4x100 (early models were 4 lug), that will give me 10 or 10.3" rears which should really balance it out nicely.
I'll likely be doing the swap at my friend's dad's shop which is just out side of Cambridge. You're more then welcome to come check it out.
I'll likely be doing the swap at my friend's dad's shop which is just out side of Cambridge. You're more then welcome to come check it out.
#17
It's just RSX calipers really. Using EP3 rotors since they are 4x100 (early models were 4 lug), that will give me 10 or 10.3" rears which should really balance it out nicely.
I'll likely be doing the swap at my friend's dad's shop which is just out side of Cambridge. You're more then welcome to come check it out.
I'll likely be doing the swap at my friend's dad's shop which is just out side of Cambridge. You're more then welcome to come check it out.
how far is just outside of cambridge. id stop by and take a look. as my rear brakes re dwarfed by my front kit
this would be a great alternative for the rear brakes. as iv had so many rear calipers seize on me
#20
Thanks bro
So after I spend 20 hours figuring out the wiring and all the hard stuff you just want my wiring diagrams.
I've got cluster pin outs, no clue if they are the same on the 90-91 though, I don't see why not. I intend to do a complete wiring diagram/list and how to once I get it all finalized.
Not sure. They just moved to a new shop like a week ago and I forget where it is.
It's a Megan Racing one for a EF bought it from --------.
I'd personally spend the money on an EM Racing one, much better quality.
I like em but then I have to give up my privacy cover.
I've got cluster pin outs, no clue if they are the same on the 90-91 though, I don't see why not. I intend to do a complete wiring diagram/list and how to once I get it all finalized.
I'd personally spend the money on an EM Racing one, much better quality.
I like em but then I have to give up my privacy cover.
#22
yea, the i wont really be needing my privacy cover, because its going to be strictly track, but yea, yours is going to be daily, so that would make a difference.. lol. I wanna see the wiring diagram too!
#25
LOOKING SEXY!!!!!!!!!!! I love it all bro. the cluster is something a lot of us are gonna want to do as well.. i wont lie. I also love the nsx caliper swap but what alternatives are there for the rear calipers around the same level? Im interested! lol. You must come out to one of our meets next year!
#33
Started to install the PICs last night, no good pictures because I forgot my camera.
Rears out:
Fronts out:
Then we hit a snag, I was sold the wrong forks! ARG! Partly my fault for not noticing when I bought them but still. I'm not dropping any names yet, going back there when they open this morning and hopefully get the right ones or a refund.
So for now I'm riding on PICs in the rear and Teins up front lol. Also the rear is a lot lower because the PICs are shorter, tucking tire in the rear and like 3" up front LOL.
I'll be getting the front PICs in tomorrow, hopefully won't have a problem getting the right forks today. I also need some bolts and washers to hook my sway bar back up with the Megan arms. The arms were the same length as stock too.
On the plus side, the PICs are friggin STIFF!!
Rears out:
Fronts out:
Then we hit a snag, I was sold the wrong forks! ARG! Partly my fault for not noticing when I bought them but still. I'm not dropping any names yet, going back there when they open this morning and hopefully get the right ones or a refund.
So for now I'm riding on PICs in the rear and Teins up front lol. Also the rear is a lot lower because the PICs are shorter, tucking tire in the rear and like 3" up front LOL.
I'll be getting the front PICs in tomorrow, hopefully won't have a problem getting the right forks today. I also need some bolts and washers to hook my sway bar back up with the Megan arms. The arms were the same length as stock too.
On the plus side, the PICs are friggin STIFF!!
#34
Got the front PICs in today. Had to argue a bit to get the proper forks but I got them.
Extended top hats on the front
What I had to do to bolt my sway bar back up again. It's ghetto but it works.
Couple over all pictures of the car.
The rear is lower then the front but I'm too lazy to adjust it and it's winter time. Come spring it will come down a bit lower.
Oh and remember, when driving, you've got to listen to good music.
Extended top hats on the front
What I had to do to bolt my sway bar back up again. It's ghetto but it works.
Couple over all pictures of the car.
The rear is lower then the front but I'm too lazy to adjust it and it's winter time. Come spring it will come down a bit lower.
Oh and remember, when driving, you've got to listen to good music.
#37
Total JDM, it took a bit of fighting but I got the right ones.
The forks they sold me were DC forks. DA forks have a smaller hole for the shock since the shock mount is smaller.
The car was sitting on ITR spec Teins, hence why I need new forks.
Thanks.
She'll be really slammed come spring.
The forks they sold me were DC forks. DA forks have a smaller hole for the shock since the shock mount is smaller.
The car was sitting on ITR spec Teins, hence why I need new forks.
Thanks.
She'll be really slammed come spring.
#39
Thanks, need to be evened out though.
Did a junk yard run with Tristan and some other people today. I forget the other guys names lol.
I picked up a new cluster trim piece (had so many friggin problems getting them out, finally got one out in one piece), passenger side door lock switch trim, 4040 prop valve and OEM exhaust tips (w00t).
Did a junk yard run with Tristan and some other people today. I forget the other guys names lol.
I picked up a new cluster trim piece (had so many friggin problems getting them out, finally got one out in one piece), passenger side door lock switch trim, 4040 prop valve and OEM exhaust tips (w00t).