I have a 94 teg, and my side moudlings are ugyl grey, and id like to remove them, is it hard and how do I do it! :GrinDev:

 

yikes. i did it on mine cuz i got t-boned and my friend at the shop got a scrap type r and put the door and quarter panel on my car. and had to remove to molding on the other side so it matched. anyways im not too sure but i watched a little. there's plastic clips once u remove the molding and there's about 5 square holes. he weld little metal pieces to cover the holes and hammer it down to make ti flush and cover it with body filler and sand it down. then primed and paint. i dunno if this helped or anything. if anyone know a better way. feel free to post.

 

oh so there held on with clips? i was hoping it was glue like most other cars

 

yeah, i know what u mean. i used to help out at the shop and some cars just use very sticky 2-way tape and it does the job. i wouldnt do it unless its done professionally. i helped out and im not too great at body work and i try.. but when the square holes used to be. i see little paint bubble coming through. maybe little rust is coming in from there or something. i only did it cuz i had to to make it look even. other than that i wont. but its ur choice if u want a type r look. too much work i'd say

 

Ya the moldings are held on by clips and you have to remove the interior pannels to access the clips from the inside. And than they just pop out I believe. Haven't done this yet but I will be and I have removed my interior pannels and I am able to see the clips from there.

 

the dude at the shop just ripped it out and broke the clips. and just pull out the clips with needle nose pliars

 

i removed mine last summer with fuzzylsbro and had them painted...there are about 5 clips per side. Some come out easier than others so you may have to use a bit of force to pull them out. Pliers are definitly the best way to remove them. Once you do that, its wise to clean out the sides and spray rust proof agent. In case of rust, do a quick wet sand around the rusted areas and use a bit of primer.

 

Do any of you guys acutally have any of those moulding that you guys took of in hand,
If you have the passenger side quater panel moulding i will take it off you guys for your price thanks in advance.

pm me.

 

hmm there's a 50/50 chance that i might. its still in the car. i took it from the shop but im not sure if its driver or passenger. i'll check tomorrow for you. problem is that it's white.

 

that;s not a problem im going to painted it anyways.

thanks for looking.

 

uh oh, good news and bad news and good news... good news is that i got it, and it is for the passenger side. bad news is that im not sure if its for an integra anyways. ---- i dont have anything to measure it with. but the back of it has 3 clips. but only 2 clips remaining. which is ok. last good news is. its free if u wanna pick it up from newmarket. shiiit should i drive around comparing it to other tegs on the street?

 

he means the side moldings, not the side skirts. fossy fish.

 

if you can do me a favor and make sure its for an integra or just give pm me your contact number and i will come and pick it up from your locations.

thank you

 

yea i just realized that earlier on today..lol, but whatever...mouldings, skirts...same ----....lol


btw who u calling fossyfish, pusshole!? :laugh1:

 

i'll try. lets hope i dont get shot using it to compare on other people's car. i'll tell u by the end of today

 

mouldings are different than sideskirts......

ya heeeeediotboi. :laugh1:

 

yea i know thanks..i didnt realize that..i know what mouldings are fossyclot but i was so confident that i knew what i was talkin about that i just blurted my 2 cents out..lol

 

^well next time. stop. pull your head outta your ***. stop thinking bout dhal, and give the right answer battyclat. :laugh1:

btw:

 

LOL OMFG......wow....that made my night :laugh1: :laugh1: :laugh1: