Python Car Alarm Install - Model 902 (pics)
** I am not claiming this is a DIY article. Just a play by play that is fairly thorough**
Purpose: As I start cleaning this car up and adding mods, I wanted to make sure the car was secured with a decent 2 way alarm. Total Cost: Alarm + Install @ Selective Sound in Mississauga. PYTHON 902 2 WAY ALARM SYSTEM $299.99 INSTALLED as per his GTcars.ca post. Time: Total time (I only snapped pics) was 2.5 hours for 2 professional installers. Difficulty: There is no doubt that this is for an experienced DIY. The tricks that the staff at Selective Sound used to get it done was awesome. My follow along, pics and notes does not do them justice. These guys were quick and very professional. Play by play First off, I was very fortunate that Davis & Max allowed for me to capture the images of their work. They have a nice customer waiting area but they knew I wanted to document this for other teg owners. Things to note. The alarm brain is not shown in these pics as to where it was placed. 2 installers worked on the car. I did not do the work. This is not an easy DIY project, so I suggest you contract Davis @ Selective Sound. This is for those who want to take a stab at it. What comes with the Python. https://www.torontointegras.ca/image...gras-00001.jpg The key fobs. https://www.torontointegras.ca/image...gras-00002.jpg The brain all wired up and ready for the install. https://www.torontointegras.ca/image...gras-00003.jpg Tape on the fuses so they don't vibrate out. https://www.torontointegras.ca/image...gras-00004.jpg Removing lower dash peices, Phillips screwdriver will do :) https://www.torontointegras.ca/image...gras-00005.jpg Removing lower dash brace, 10mm ratchet. https://www.torontointegras.ca/image...gras-00006.jpg https://www.torontointegras.ca/image...gras-00007.jpg Lower dash brace. https://www.torontointegras.ca/image...gras-00008.jpg Drilling for hood pin. https://www.torontointegras.ca/image...gras-00009.jpg The hole for the hood pin. https://www.torontointegras.ca/image...gras-00010.jpg Installing the hood pin. https://www.torontointegras.ca/image...gras-00011.jpg These next 3 photos show the fuse box area before the install. https://www.torontointegras.ca/image...gras-00012.jpg https://www.torontointegras.ca/image...gras-00013.jpg https://www.torontointegras.ca/image...gras-00014.jpg Removing a nut and bolt to mount the alarm horn. https://www.torontointegras.ca/image...gras-00015.jpg Stripping wires. Take your time as to not cut right through. https://www.torontointegras.ca/image...gras-00016.jpg Passing a coat hanger through the firewall into the cabin. This includes the horn wires and the pin wires. https://www.torontointegras.ca/image...gras-00017.jpg Soldering ignition wires. https://www.torontointegras.ca/image...gras-00018.jpg Smiling at his nice job. lol https://www.torontointegras.ca/image...gras-00019.jpg Taping it all back up. https://www.torontointegras.ca/image...gras-00020.jpg hood pin and horn all installed. https://www.torontointegras.ca/image...gras-00021.jpg Pulling the kick panel off to access the door and trunk wires. https://www.torontointegras.ca/image...gras-00022.jpg More wiring for the doors and trunk. https://www.torontointegras.ca/image...gras-00023.jpg Remote receiver installed just behind the rear view mirror. https://www.torontointegras.ca/image...gras-00024.jpg Wire tuck behind the trim. https://www.torontointegras.ca/image...gras-00025.jpg The next two pictures show the a Pillar being opened to hide the receiver wire and the installation of the led. https://www.torontointegras.ca/image...gras-00026.jpg https://www.torontointegras.ca/image...gras-00027.jpg Wires being zip tied under the A Pillar. https://www.torontointegras.ca/image...gras-00028.jpg Wiring diagram. This is straight out of the manual. https://www.torontointegras.ca/image...9/wiring-1.jpg Wiring diagram simplified (what the installer used) https://www.torontointegras.ca/image...9/wiring-2.jpg Door and trunk wires again. Remote lock on hatch was discovered to be dead. https://www.torontointegras.ca/image...gras-00029.jpg Tester trick with a knife ;) https://www.torontointegras.ca/image...gras-00030.jpg Using the above diagram, tap into the wires, solder, close up. https://www.torontointegras.ca/image...gras-00031.jpg There next two pics show him taping it all back up. https://www.torontointegras.ca/image...gras-00032.jpg https://www.torontointegras.ca/image...gras-00033.jpg The L.E.D. install. https://www.torontointegras.ca/image...gras-00034.jpg Glued in. https://www.torontointegras.ca/image...gras-00035.jpg Fast curing glue and activator. https://www.torontointegras.ca/image...gras-00036.jpg Here are three pics of everything all taped up and getting ready to put everything back together. Super clean install!! https://www.torontointegras.ca/image...gras-00037.jpg https://www.torontointegras.ca/image...gras-00038.jpg https://www.torontointegras.ca/image...gras-00039.jpg Warning L.E.D. all installed https://www.torontointegras.ca/image...gras-00040.jpg All done, sorry no pics of where the brain ended up. The thieves will have to figure that one out for themselves. lol https://www.torontointegras.ca/image...gras-00041.jpg Blinking lights don't show up well in pictures. lol https://www.torontointegras.ca/image...gras-00042.jpg |
ima come by and test this sucker out late at night
looks good. DIY don't look too bad though. |
lol nice i will turn up the sensitivity then and wait upstairs with a b b gun. lol
|
You should of went with at least compustar, Python is really cheap
|
Originally Posted by k1e1v1i1n
(Post 273966)
lol nice i will turn up the sensitivity then and wait upstairs with a b b gun. lol
|
Originally Posted by ls/vtec
(Post 273969)
You should of went with at least compustar, Python is really cheap
|
what makes the python more better then the compustar??
|
he said way in the post directly above yours
|
Originally Posted by selective sound
(Post 274096)
Actually the Python is not a cheap alarm at all, it is made by the same people who make Viper and it has way more built in features than Compustar does.
|
Originally Posted by KjB
(Post 274254)
what makes the python more better then the compustar??
|
All times are GMT -5. The time now is 06:12 PM. |
© 2024 MH Sub I, LLC dba Internet Brands