96 GSR w/Built Motor
Hey guys, Its time to sell my gsr to make room and money for a new car. I've had a good time with it but im just not interested in the honda scene anymore, so heres the info.
Exterior:
-96 Integra GSR Silver 2dr (no RUST, just some bubbling, and the front left fender and bumper has damage from a fender bender in the winter)
-16" Rota Grid Wheels with Falken Azenis RT615 (205/40/16) 70% tread
-Type R wing
Performance:
-Built GSR 1.8L (pro1 cams, pro valvetrain + cam gears, skunk2 flatface valves skunk2 manifold, wiseco forged 12:1 pistons, eagle esp rods, ARP rod bolts and headstuds. ALL new oem seals and gaskets, i can go into more detail PM me)
-GSR tranny, no grinds or scratches with a new clutch 10,000 km ago
-Hondata S300 in a P72 and Innovate LC-1 Wideband (not installed), car was street tuned so its safe to drive.
-Edelbrock header + WS2 exhaust (i have Megan Racing header, Magnaflow spunbody cat and res available, still in boxes)
Others:
-New brakes 3000 k ago...Brembo Rotors with EBC Yellow pads all around.
-The timing belt, coolant, tranny fluid are all brand new from when i did the swap 2 weeks ago.
-Sony MP3 deck.
-Compustar 2 way paging alarm w/remote start
-Tokico Blue shocks with H&R Sport springs.
-New L+R tie rods a couple months ago.
-Rear toe links were done 4 months ago and alignment at the same time.
Will post pics when i go on my desktop tommorow, i have pics of engine build as well if interested, engine was built by me but everything was prechecked/measured at Candian Cylinder Head.
Asking $6500 OBO AS IS. A little flexible on price. I invested more in just the engine alone than im selling it for.
Contact Kraz, Located in Brampton
-PM me here
-Cell 647-407-5729, i'll call back if i don't answer
-email : kraz_13@hotmail.com
)
whole front left damage

close up
basiclly needs a fender and bumper sprayed.

Interior

Engine



the "rust" on the rear 1/4s. Both sides are the same.

Passanger side is mint.

Rim/Tire
Exterior:
-96 Integra GSR Silver 2dr (no RUST, just some bubbling, and the front left fender and bumper has damage from a fender bender in the winter)
-16" Rota Grid Wheels with Falken Azenis RT615 (205/40/16) 70% tread
-Type R wing
Performance:
-Built GSR 1.8L (pro1 cams, pro valvetrain + cam gears, skunk2 flatface valves skunk2 manifold, wiseco forged 12:1 pistons, eagle esp rods, ARP rod bolts and headstuds. ALL new oem seals and gaskets, i can go into more detail PM me)
-GSR tranny, no grinds or scratches with a new clutch 10,000 km ago
-Hondata S300 in a P72 and Innovate LC-1 Wideband (not installed), car was street tuned so its safe to drive.
-Edelbrock header + WS2 exhaust (i have Megan Racing header, Magnaflow spunbody cat and res available, still in boxes)
Others:
-New brakes 3000 k ago...Brembo Rotors with EBC Yellow pads all around.
-The timing belt, coolant, tranny fluid are all brand new from when i did the swap 2 weeks ago.
-Sony MP3 deck.
-Compustar 2 way paging alarm w/remote start
-Tokico Blue shocks with H&R Sport springs.
-New L+R tie rods a couple months ago.
-Rear toe links were done 4 months ago and alignment at the same time.
Will post pics when i go on my desktop tommorow, i have pics of engine build as well if interested, engine was built by me but everything was prechecked/measured at Candian Cylinder Head.
Asking $6500 OBO AS IS. A little flexible on price. I invested more in just the engine alone than im selling it for.
Contact Kraz, Located in Brampton
-PM me here
-Cell 647-407-5729, i'll call back if i don't answer
-email : kraz_13@hotmail.com
)
whole front left damage

close up
basiclly needs a fender and bumper sprayed.
Interior

Engine



the "rust" on the rear 1/4s. Both sides are the same.

Passanger side is mint.

Rim/Tire
Last edited by Kraz13; May 10, 2008 at 06:40 PM. Reason: added pics.
bumper IS reusable, just the paint and primer are scraped off no actual damage to plastic.
fender on theother hand would be cheaper to just replace. You can find them on here for like $40-80. I wouldn't reuse it, it will never be perfect.
fender on theother hand would be cheaper to just replace. You can find them on here for like $40-80. I wouldn't reuse it, it will never be perfect.
Thread
Thread Starter
Forum
Replies
Last Post
ThaWeezord
Integra Parts For Sale
39
Dec 20, 2008 08:16 AM
ThaWeezord
Integra Parts For Sale
14
Oct 15, 2007 07:48 PM
jmilljay
Integras For Sale
5
Apr 14, 2007 06:20 PM



