Taking Lens Off JDM Headlights
Hey
I have tried using a heat gun and slowly opening the lens with a flat head screw driver. This doesnt seem to working very well at all it isn't getting me anywhere. id like to know if this is the only way and it just takes a LONG time, or is there a better easier way? |
I've used this method before. It wasn't bad. You need two people though.
|
put it in the oven. it'll heat more evenly
|
Use an oven. are you doing a retrofit on a JDM Gen2 (Pre-1993) or JDM Gen 3 (95-00) integra headlights?
If you are doing any kind of HID retrofitting then head over to www.HIDplanet.com they have everything you need to know about HID retrofitting via their forums. |
i have a similar question.. i have jdm dc2 headlights and want to open up the lens, if anyone has ever done this any tips?
|
They don't fit in the oven.
|
^You have a shitty oven........ :D
James |
Originally Posted by SIC1
(Post 155449)
Use an oven. are you doing a retrofit on a JDM Gen2 (Pre-1993) or JDM Gen 3 (95-00) integra headlights?
If you are doing any kind of HID retrofitting then head over to www.HIDplanet.com they have everything you need to know about HID retrofitting via their forums. |
200 degrees for 10-13 min. That's what the civic guys put it in for. Any longer your lense will burn out (turn yellowish). But like I said, JDM DC2 headlight wont fit in most ovens. Try yours out...never know
|
200 degrees on what setting (bake or w.e else there is) and is that 200 degrees for 10-13 minutes for one headlight at a time or both together??
|
Originally Posted by JDM_gsR
(Post 155582)
200 degrees for 10-13 min. That's what the civic guys put it in for. Any longer your lense will burn out (turn yellowish). But like I said, JDM DC2 headlight wont fit in most ovens. Try yours out...never know
|
hey jdmhonda im doing the same thing and ive been reading around, maybe try using some silicone disolvent? that might help the process if your doing it with a heatgun but try to find some that doesnt harm the housing..
|
One person to hold it, one person to use the heat gun. Both pull it apart slowly frequently while still using heat gun.
|
sounds good thanks for the help everyone :)
|
does anyone else have any ideas? jdmhonda did you get it off yet? if you did could you give me any more tips?
|
Originally Posted by JDM_gsR
(Post 155764)
One person to hold it, one person to use the heat gun. Both pull it apart slowly frequently while still using heat gun.
Anyone care to comment on what products / methods they used to clean this inside and out. Also, what did you guys use to seal it back up so they don'y get hazzy again? |
Originally Posted by ninja
(Post 155857)
Good timing with this tread, I was hoping to do this sometime this month...
Anyone care to comment on what products / methods they used to clean this inside and out. Also, what did you guys use to seal it back up so they don'y get hazzy again? |
Originally Posted by phoms
(Post 155854)
does anyone else have any ideas? jdmhonda did you get it off yet? if you did could you give me any more tips?
|
Use plain old windex with paper towels. Not sure which silicone I used to seal it.
|
The headlight come apart in 3 pieces. Lense, black housing and the rear. Be careful cause the plastic might be soft.
|
if they dont fit in your oven go to the nearest PIZZZA PIZZA they'll fit in their oven and the lens will separate in no time. 967 11 11 is the number btw.
|
^^ i wish they would do it...id take it there in one second
|
oh ---- i never thought about that.. my cousins owns a pizza pizza.. lol, or i could try the oven at my gfs restaurant.. but that sh*t is way too hot
|
Originally Posted by JDM_gsR
(Post 155931)
The headlight come apart in 3 pieces. Lense, black housing and the rear. Be careful cause the plastic might be soft.
|
Originally Posted by GSR_gino
(Post 156013)
if they dont fit in your oven go to the nearest PIZZZA PIZZA they'll fit in their oven and the lens will separate in no time. 967 11 11 is the number btw.
^LOOL how do i save this to my signature |
Originally Posted by JDMHONDA
(Post 156091)
would you happen to know if the chrome parts in the headlight detatch from the back peice or is it attatched??
|
Originally Posted by JDM_gsR
(Post 156140)
Back or black piece? Black piece is detatched. Lense, housing, then back piece w/ chrome.
|
i think he means the chrome part thats around the headlight.. like the reflective part.. you dont really want to mess around with the reflective stuff. why do you wanna take that off?
|
Originally Posted by phoms
(Post 156182)
i think he means the chrome part thats around the headlight.. like the reflective part.. you dont really want to mess around with the reflective stuff. why do you wanna take that off?
|
Anyone find out about what silicone sealant to use?
|
any silicone will work
|
i know you guys are talking about the dc headlights i have a DA iwas just wondering what can i use to clean the lens?
|
Originally Posted by delta13
(Post 156376)
i know you guys are talking about the dc headlights i have a DA iwas just wondering what can i use to clean the lens?
|
All times are GMT -5. The time now is 09:25 AM. |
© 2024 MH Sub I, LLC dba Internet Brands